pbskids

 |   |   |  S2K Trans Rebuild
Subscribe to the Free
Newsletter

S2K Trans Rebuild

Synchrotech gets us back in gear

Rodrez
Dec 18, 2013

Technical Guidance and Captions by James Ornelas

In the previous installment of Project AP1, Golden Eagle was taking care of the F20C bottom end, prepping it for InlinePRO's F24 stroker kit. The chassis, after having spent a few days at the Rywire.com facility, was shipped to ASC Speed-Metal for some fab work before it eventually receives a fresh coat of paint under the hood in the near future. That left the transmission to collect dust and I figured it would be a great time to freshen it up.

I ed James Ornelas of Synchrotech who suggested I bring the transmission to their facility to disassemble, inspect and clean up the inner workings. If you're not familiar with the name, Synchrotech has been in business since 2008. CEO and president, David Henson was previously employed by a company that had decided to discontinue their performance division. Seizing the opportunity to set out on his own, Henson purchased what was left of the companies inventory and opened the doors to Synchrotech Transmissions Inc. Henson and his team went on to research and develop carbon-lined synchros, a lengthy process that took well over a year to perfect. Well known for their ability to withstand high RPM and high horsepower abuse, the synchros became a hit with D-, B-, and H-series transmission users. Just a few years later that same technology was put into K-series transmission synchros, and more recently, Synchrotech introduced their own hardened steel sleeves, hubs, and carburized synchro springs to compliment their carbon synchro sets.

Beyond the performance realm, Synchrotech has a steady stream of your average, street-driven Honda transmissions to inspect and repair as well. And trust me when I say, this workshop runs like a well-oiled machine and is in constant motion. The years of experience and parts development assured me Synchrotech would have no problem making quick work of my S2K's tranny. Upon inspection, Ornelas states, "The transmission was in impeccable shape. We noticed minimal damage with the secondary drive gear and bearing assembly, as well as the reverse sleeve center hub. The gear had some pattern wear and the bearing was getting a little on the noisy side. The reverse hub had some base wear as well as the distance collar, so we replaced those. The rest of the transmission was in really good shape!"

I followed along to snap a few pics as technician Steve Vasquez reassembled the trans:

  |  
1. The AP1 transmission internals are prepped and laid out on the bench for final inspection before assembly will begin.
  |  
2. Synchrotech incorporates a deburring process in all of their builds. Using a custom selected ceramic-based media; parts are placed in vibratory machines creating a polishing/cleaning effect. This helps reduce friction and encourages intersecting parts to work in conjunction effortlessly.
  |  
3. Every gear will have the synchro clearances checked prior to assembly.
  |   4. Needle bearings and distance collars are well oiled during assembly using Honda MTF. This is a crucial step to avoid a dry start up
  |  
5. The 1-2 sleeve assembly is being placed over Second gear on the countershaft. Most of the sleeve sets available from Honda now come with carbon synchros. Keep that in mind when requesting them from your local synchro supplier ;)
  |  
6. After First gear is placed over the 1-2 Sleeve assembly, next will come the reverse gear and reverse sleeve assembly. Topping that off will be the bearing, which will need to be pressed or driven onto the shaft.
  |  
7. Next a new countershaft top nut is installed and torqued to spec. Be sure to stake the nut using a chisel or punch to lock it in place.
  |  
8.The mainshaft (front) and countershaft assemblies are complete and ready to be installed along with the forks.
  |  
9.Steve carefully drops the completed shaft and fork assemblies into the clutch housing case.
  |   S2K Trans Rebuild
  |  
10-11. Not all transmissions are created equal. Locking in the countershaft lower bearing clip can prove to be a difficult task at times and may require an extra hand. Here Ornelas gives the assist.
  |  
12. Here is the clutch housing with a partially assembled fork set.
  |  
13. Next the shift rod is installed into the interlock and shift arm assembly. Be sure to use a new spring pin.
  |  
14. Countershaft access bolt is then installed.
  |  
15. Put a nice bead of Hondabond onto the clutch housing case sealing surface and allow it to tack up for a few minutes before installing the main case. These 8mm bolts will be torqued to 20 ft-lb.
  |  
16. Install the secondary drive gear and bearing using a driver, then torque to 127 ft-lb. You will need a mainshaft holder for the portion to keep the shafts from spinning when torqueing the nut. This nut will also need to be staked to keep from backing out.
  |  
17.After installing the end bearing and seal, next you will drive on the companion flange onto the secondary shaft. Once that is complete a new O-ring and nut will need to be installed and torqued to 119 ft-lb. This nut will also need to be staked in place to prevent it from backing out.
  |  
18.Be sure to apply a grease lubricant on the bearings to prevent a dry startup.
  |  
19. Apply a layer of Hondabond on the main case and allow it to tack up before installing the tail shaft assembly. These 8mm bolts will also be torqued to 20 lbf-ft. And that’s all she wrote. The transmission has been freshened up and is ready for duty.
  |  
Synchrotech now offers its own line of brass synchros with an improved lock angle and updated tooth pattern. For those craving more performance, they offer their Pro Series line of Carbon Composite-lined synchros that feature an improved lock angle, tooth pattern, strengthened brass body and bonding process to handle more HP and aid in high RPM shifts.
  |  
Synchrotech also added its own line of hardened sleeves and center hubs for most Honda performance applications. The hardening process is done during manufacturing to help strengthen the sleeves and hubs to offer longer life and improved performance. This is a great alternative to OEM sleeves that are costly and require you to buy the complete sleeve set.

Sources

Synchrotech Transmissions
San Dimas, CA 91773
949-592-5900
By Rodrez
573 Articles

BROWSE CARS BY MARKET

MORE HOW TO

To many, the way a shock works is a bit of a mystery. We pull back the curtain a bit and go over the basics behind your shocks.
Justin BannerApr 18, 2018
Honda's K series has enjoyed a tremendous tenure of performance, but there's a new engine on the block.
Evan PerkinsMar 23, 2018
The latest and greatest
RodrezMar 23, 2018
The road to 1,000 horsepower from pro drifter RAD Dan Burkett's Toyota 2JZ-GTE inline-6 engine ends here.
Bob HernandezMar 20, 2018
In order to prep a B-series for an AEM Infinity EMS we add a number of AEM sensors to help monitor vitals in the quickest, most precise way possible
RodrezMar 14, 2018
Join Our FREE

Sign Up today for our FREE Newsletter and get the latest articles and news delivered right to your in-box.

Sponsored Links

SEARCH ARTICLES BY MAKE/MODEL

Search
CLOSE X
BUYER'S GUIDE
SEE THE ALL NEW
NEWS, REVIEWS & SPECS
TO TOP