|   |   |  Project Acura RSX Type S Brake Test - Tech
Subscribe to the Free

Project Acura RSX Type S Brake Test - Tech

Splitting Hairs Between Stopping Short And Stopping Safe

Jay Chen
Oct 1, 2007
  |   Project Acura RSX Type S Brake Test - Tech

Tires stop a car, not brakes. Even if that's a broad statement, full of caveats and qualifiers, it contains a crucial truth. All things being equal, stopping distance is stipulated by how much grip the tires have before they're finally overcome by braking torque, resulting in wheel lock. For those with ABS, the surest and simplest way to reduce dead-stop braking distance is a simple matter of stickier tires.

So how do big brake companies go about claiming improved braking performance without changing tires? The answer: braking balance. And that's the reason why we devoted two whole days to comprehensive brake testing, one of which was completely unanticipated.

As you might have seen from various Project RSX pictures, a set of StopTech brakes were already installed when we inherited the car. It's a complete set-up, engineered to optimize braking performance through better front-to-rear balance. The kit consists of stainless steel braided brake lines, 328x28mm (12.9x1.1-inch) slotted two-piece, fully floating rotors with aluminum hats for the front, four-piston fixed squeeze-forged aluminum calipers with StopTech's patented X-brace bridge design, Axxis Ultimate pads for the larger front and stock rear calipers, and all the necessary hardware and brackets to mount the larger front brakes. We never mentioned them before because we hadn't got around to doing a full brake test involving A/B comparisons with the stock hardware. Now that the completed Project RSX is ready for its final performance figures, it was the perfect time to break out the testing gear.

Our comprehensive brake test program involves 10 repeated 80-to-0mph runs, measuring rotor temperatures on each run as well as the total braking distance. The first measurement is performed with rotor temps at near-ambient prior to the run, so we have a more complete picture of stopping performance over a broad temperature range. And since modern brakes are so damn good at stopping in spite of high temperatures, we also do an 80-to-0mph run on the unmeasured outbound trip, in order to keep brake temps up and try to get stock systems to fade.

Day OneWe took Project RSX out to the track with the StopTechs already installed, pads properly bedded and the system pre-bled with fresh Motul RBF600 brake fluid. Conditions would be more or less ideal: using the same track on the same day on the same relatively fresh Hankook Ventus Z212 maximum-grip tires. Having conducted this test countless times, we have a decent idea of what constitutes a good braking distance for a car of this weight and how much variation to look for as the brakes heat up. Project RSX averaged an 80-to-0mph braking distance of 219.8 feet (disregarding the first cold stop) with a best of 213.3 feet. We expected nothing less.

For you statistics nerds, that amounts to a standard deviation of (or 68 percent of all stops falling within) 5.1 feet from the average braking distance. This is almost nothing compared to the variations we see in most ABS-equipped cars with modified brake components. Front and rear rotor temperatures were within 160 degrees F of each other, even with the dust shields installed.

After a quick lunch to let the rotors cool, we took off the StopTech kit and installed stock RSX Type-S front rotors and calipers, using Acura's A-spec pads. We left the braided lines on to keep things fair and re-bled the whole system. With the new pads properly bedded and heat-cycled with an evenly distributed transfer layer of the new pad material on the rotors, we repeated the test.

We expected to see much higher front rotor temperatures, a squishier pedal feel and maybe even some brakes on fire at the end of the runs. With any luck, the stopping distances would be just a little longer than the numbers collected earlier with the StopTech system, but not so different as to throw out our grandiose claim of tires making the most difference.

On its stock brakes, the car did everything we expected, but also posted a shorter braking distance on almost every corresponding brake run. On average, the stock brakes stopped the car in 216.1 feet, 3.7 feet shorter than the StopTech average. It also posted its best distance of 210.6 feet on the fifth run, even with the pedal going soft and the pads billowing smoke.

Obviously, these numbers were going to piss on StopTech's parade and ours. Even though the big brakes were far superior in terms of rotor temperatures, pedal feel and modulation, the longer-than-stock stopping distances would undoubtedly raise some questions as to the validity of spending several thousand dollars on an upgrade. And even though we'd prefer some semblance of pedal feel on the track with the big brakes over a negligible difference of less than four feet (remember this is still within one standard deviation of the data collected), it's still a little embarrassing.

We consulted with StopTech's engineers and sent them our data, so they could defend their product before we blasted them with our published automotive blasphemy. They agreed our testing methodology was decent enough for a bunch of magazine weenies and that the longer braking distances were probably on account of the modifications made to Project RSX, and possibly slight changes to the ABS calibration and braking hardware on the newer 2005 RSX Type-S. StopTech had performed extensive testing of its Type-S kit on a then-new 2002 model with springs and street tires, and was able to obtain favorable braking performance in every parameter. Our car far exceeds the capabilities of StopTech's test vehicle.

Break Out The Pocket CalculatorsSo the problem really lies in brake balance. Acura did such a good job on the balance of the Type-S system that little to no room was left for improved braking distances, given the same set of tires. It already has the ideal brake balance to virtually maximize each tire's grip, while at the same time keeping the car stable during on-the-limit braking. To understand this, we're going to have to dust off the calculators and slide rules and run through some numbers.

In order to maximize stopping performance, each tire should be just near its limits of grip in deceleration. Most cars off the showroom floor have a front-biased brake system, which is much safer for the average driver in a panicked braking situation-more rear bias at the limits of grip will cause the car's tail to get loose, even in a straight line. Not a good thing when braking and turning at the same time, unless you're doing it deliberately on a track.

The cost of the greater front bias is more braking grip from the rear tires. In the case of the RSX, Acura's engineers found a way to make a safe street car that still had excellent brake balance and optimized tire grip on all four corners, making it that much harder for big brake kit manufacturers.

To maximize the work that both the front and rear tires are doing, it's logical to say that you want to generate the same amount of braking torque (created by the calipers on the rotor).

Braking torque is a function of several factors, like the frictional coefficient of the pads against the rotors, the effective radius of the rotors (since larger rotors mean longer force moments), hydraulic fluid pressure pushing against the brake pistons, and the pistons' total surface area. Multiply everything together for a simple equation that shows how much braking torque can be exerted on each corner.

It's pretty intuitive if you separate the equation into sections and have a simple understanding of physics. Friction between any two objects is a factor of frictional constant- (mu)-between the two surfaces (determined by its physical characteristics) and the force that's pushing down on it. So in the case of brakes, friction is just the total amount of force pushing the pads against the rotors times the friction coefficient of the pad material on the rotor.

Contrary to what many might think, total pad area doesn't play into the equation because (which is determined experimentally) is dimensionless, or unit-less, and already accounts for the area of the pad. The advantage of pad area is mostly in wear and increased thermal mass.

The force pushing down on the pad is the area of the pistons multiplied by hydraulic pressure of the brake fluid pushing at the back of each piston. Much like a wing, pressure pushing on one side (let's say it's 100psi) times the surface area (let's just say there are two square inches of piston area on one side of the caliper) will yield a total of 200 pounds of force pushing the pad against the rotor. If the caliper is a fixed version with identical pistons on both sides, then add a factor of two to the equation.

The amount of friction force has now been determined. That force is stopping the wheel from spinning by exerting torque on the brake rotor. Torque is a force exerted on an object at a given radius causing it to rotate.

Since a rotor is already turning in one direction and torque generated by friction is, by definition, in the opposite direction, torque created by a brake pad acts to slow the rotor down. In geek: braking torque is expressed by friction force multiplied by the effective radius of the rotor.

The effective radius of the rotor is basically the radius at which the average amount of braking work is done. Different brake manufacturers use different methods to approximate the effective radius, but for the most part, it is larger than the centerline radius of the brake pads, since the outside of the pad travels a longer distance and does more work than the part of the pad closer to the center. Multiply all this together, and you have braking torque created at the rotor.

In terms of balance, the same equation can be applied to the front and rear brakes. Even without plugging in any numbers, we know rear brakes will yield less braking torque than fronts because they have a smaller radius, less piston area and probably less hydraulic pressure from the factory proportioning valve.

There are two reasons why rear-wheel braking torque is less than the front, even though we want to get the most work out of the rear tires. In addition to safety and stability under braking, the other factor we've ignored so far is weight transfer. Under braking, weight shifts forward, so the front tires do more work. With the same braking torque at both ends, rear tires lock up as weight is shifted off and available grip is diminished. Weight transfer can also be approximated by a simple equation, though the variables are hard to determine other than through experimentation.

Knowing this, StopTech's engineering team suggested a retest using their off-the-shelf RSX non-Type-S brake system, something few manufacturers offer for cars of different trim levels but the same chassis. The only difference between the two systems is a 2mm reduction of the trailing piston diameter and a conventional cast caliper instead of the squeezed-forged process used on the Type-S caliper. Everything else, including pads, remained the same.

Going back and crunching numbers in the brake torque equation, this means a six percent reduction in torque output at the front, which further shifts brake bias to the rear.

Day TwoWe were back out within a week to retest the new set-up. The lighter cloud layer and lower ambient temperatures meant surface temperatures this second day would be lower, making our tires slightly less greasy than during the previous test. There was also less wind, keeping dust off the track and reducing head- and tail-wind effects. We also (unwittingly) topped off the tank, so there was more weight in the back, contributing to more rear tire grip. Either way, results of each test should only be compared directly with other results from the same day.

To keep it fair, we started by testing the stock brakes under these conditions with the system freshly bled. We also noticed signs of possible flex on the stock front calipers from the week of street driving prior to this session. Even after the full test program, the transfer layer of pad material on the rotors had thinned radially, compared to when we just finished the first stock test.

Day two's stock 80-to-0mph braking distance averaged 211 feet, with a best of 201.2. The larger variation in this day's stock data means standard deviation had spread to 4.5 feet, still incredibly good. And again the pedal had gone soft, with pad smoke galore. Under full ABS intervention, Project RSX felt slightly more darty than on day one, indicating more rear bias-probably on account of the full tank. Stock results from day two were as we expected: a little better, considering the changes in conditions.

Following the same bleeding and bedding procedures, we installed the non-Type-S calipers and did the whole process again. Apparently, StopTech's engineers know what they're talking about, as stopping distances on most respective runs were as good, if not better, than stock. Average stopping distance dropped to 208.7 feet, which is still splitting hairs in our opinion, but at least it's a reduction of average braking distances of just over two feet. The best braking distance, however, was still a foot shy of stock. Pedal feel with the StopTech hardware was just as good as the first day and rotor temperatures exhibited the same trends.

The Secret To Stopping Five Feet ShorterWe're pretty happy that our premise of tires doing the braking still holds, as our data shows. In most other cases (outside of a highly refined sports chassis like the RSX), we'd expect a properly engineered kit to easily outperform stock brakes both in feel and consistency. In the case of hair-splitting on Project RSX, the secret was to further increase rear bias through proper piston sizing-the best way to adjust braking torque without changing pad friction characteristics, rotor sizes or compromising hydraulic pressure.

If we assumed that the A-Spec pads and the Axxis Ultimate pads have the same friction coefficient, then based strictly on the piston area and effect radius alone, we'd find the StopTech Type-S kit's front calipers have a force output which is four percent greater than stock. The non-Type-S calipers actually apply two percent less than stock. That's a six percent difference just by reducing two of the four pistons by 2mm in diameter.

For simplicity's sake, if we ignored the effects of different pad friction characteristics and assumed it was all the same, applied these calculations to some other front brake kits on the market based on the published piston sizes and rotor diameters, then we get an idea of where other brands might stand relative to stock in terms of front caliper force output.

One brand goes much higher, while the other is even lower than the StopTech non-Type-S kit. Although the change in force output/braking torque in front doesn't necessarily dictate overall brake bias (since some manufacturers don't indicate which pads are used in the rear), it does give a reference for how to set up a braking system.

And just because it worked on our RSX Type-S doesn't necessarily mean you should do it too. Our car has been seriously tweaked: significant weight reduction, lowered center of gravity and a much stiffer suspension; all things a brake kit manufacturer can't account for.

In the real world, brake engineering and balance isn't just about how fast you can stop. Brake engineers and OEMs know this, and it's the last piece of the puzzle we didn't get to test between the three set-ups. Often ignored in the aftermarket, braking stability in a turning/braking situation plays a critical role.

The Society of Automotive Engineers (SAE) has a set procedure and protocol for this. Essentially, the test measures how a car behaves and where it ends up when the brakes are fully applied when circling a skidpad at its limits. A car with more rear bias will rotate and end up well inside the original line of travel, while a car with too much front bias will push well outside the skidpad. Maintaining a balance that allows the driver to keep going where the front wheels are pointing is critical and is also one of the factors behind StopTech using less-than-optimal rear bias in order to keep the car on line.

For Project RSX, we prefer the added feel and margin of safety offered by the StopTech kit. If three feet of braking is outside the margin of your tires and control, you're probably overdriving.

  Best (ft) Average (ft) Standard Deviation (ft)
Day 1:      
Stock 210.6 216.1 3.5
StopTech (larger front piston area) 213.3 219.8 5.1
Difference 2.7 3.7  
Day 2:      
Stock 201.2 211 4.6
StopTech (smaller front piston area) 202 208.7 4.0
Difference 0.8 -2.3  
  Percent of Stock
Manufacturer Force Output* Kit Part Number
Manufacturer 1 109** 1A2.6013A
StopTech 104 83.058.4300.xx
StopTech 98 83.432.4300.xx
Manufacturer 2 89** 140-7014
*Ignoring friction
**Calculated from data published on manufacturer's web site.
By Jay Chen
85 Articles



Making a 400-mile pilgrimage inside the luxurious, if somewhat space-challenged confines of Jaguar's latest special edition F-Type
Benjamin HuntingMar 20, 2018
Brian Duong likes being first. His FR-S is the first in the US to wear Varis' Kamikaze aero and was also the first to use GReddy's turbo system and ITBs
Aaron BonkMar 15, 2018
While the AE86 might deserve a stronger sheen in the spotlight, it's not for everyone. Jerry Cerda will tell you why he prefers the AE86's lop-eared little brother.
Micah WrightMar 12, 2018
Taking a weekend cruise from Montreal through the rustic strongholds of Sutton, Knowlton, and Lac Brome.
Benjamin HuntingMar 12, 2018
One look at J.A.S. Motorsports' race-winning resume and its easy to see why Honda chose to partner with the ultra-successful Italian race firm.
RodrezMar 9, 2018
Join Our FREE

Sign Up today for our FREE Newsletter and get the latest articles and news delivered right to your in-box.

Sponsored Links